Guide
Try-in and cementation by material
General seating and cementation guidelines by material.
For: the dentist and assistant seating the restoration.
These are general guidelines. Always follow the instructions of the cement and primer manufacturers.
Our zirconia and e.max are Ivoclar materials, so Ivoclar's own protocols apply directly. The Ivoclar Cementation Navigation System is a free tool that recommends a cement for the restoration and the tooth or abutment, and shows each step.
Try-in
- Check proximal contacts first, then marginal fit, then occlusion.
- Evaluate the shade with a try-in paste or water before cementation, particularly for e.max and veneers.
- After try-in, clean the intaglio surface. Saliva contaminates zirconia and reduces bond strength; use a cleaning agent made for the purpose or air abrasion, not phosphoric acid.
Zirconia (IPS e.max Zirconia)
Ivoclar indicates three cementation methods for IPS e.max Zirconia crowns and bridges. After try-in, clean the bonding surface with Ivoclean.
| Method | Restoration surface | Ivoclar luting material | Preparation |
|---|---|---|---|
| Conventional | Clean with Ivoclean | ZirCAD Cement | Retentive: 4 to 8 degrees, at least 4 mm high |
| Self-adhesive | Clean with Ivoclean | SpeedCEM Plus | Retentive: 4 to 8 degrees, at least 4 mm high |
| Adhesive | Clean with Ivoclean, then Monobond Plus | Variolink Esthetic DC | Retentive form not required |
Zirconia veneers, inlays, onlays, cantilever bridges and resin-bonded bridges are indicated by Ivoclar for adhesive cementation only (Variolink Esthetic; the light-cured version only where the material is under 1.5 mm thick).
Lithium disilicate (IPS e.max)
- Adhesive cementation is required for veneers, inlays, onlays and crowns prepared to the reduced 1.0 mm thickness. Ivoclar's protocol uses Monobond Etch & Prime on the restoration, Adhese Universal on the tooth and Variolink Esthetic.
- Crowns and partial crowns with conventional reduction (1.5 mm) may also be cemented self-adhesively or conventionally, according to Ivoclar.
- Etch and prime the restoration after try-in and cleaning, immediately before seating.
PFM and full metal
- Our PFM porcelain is Ivoclar IPS Style. It is seated like any PFM restoration.
- Conventional or resin-modified glass ionomer cement. No surface treatment is required.
Screw-retained implant restorations
- Confirm complete seating with a radiograph before final torque.
- Torque the screw to the implant manufacturer's specification.
- Protect the screw head, then seal the access channel with composite.
If a restoration does not fit
Call 484-891-1071 before adjusting extensively. A photograph, or a new scan with the restoration seated, helps us identify the cause.
Manufacturer references
Values marked "Ivoclar" on this page are taken from Ivoclar's published documentation. Refer to the current documents for complete instructions.
- Ivoclar Cementation Navigation System: cement selection and step-by-step protocols
- IPS e.max Zirconia technical guide: minimum thicknesses, preparation and cementation
- IPS e.max Zirconia: product information
- Minimally invasive crown preparation for lithium disilicate (PDF)
- IPS e.max CAD lithium disilicate: product information
- IPS e.max Press lithium disilicate: indications and cementation
- Ivoclar instructions for use
Request information
Complete the form and a member of our team will respond within one business day.
Or call 484-891-1071.
TDB Dental Lab301 S. Main St, STE 2S
Doylestown, PA 18901
Monday to Thursday, 9am to 5pm
